Company:
RBC Bearings
Location: San Francisco
Closing Date: 07/11/2024
Hours: Full Time
Type: Permanent
Job Requirements / Description
Experience: High school diploma or general education degree (GED), and a minimum of one year of experience in precision bearing assembly using a variety of precision checking techniques.
Knowledge/Skills/Abilities:
Competence to interpret blueprints and decipher documents such as safety rules, operating and/or procedure manuals. Competence to use standard measuring equipment. Ability to add, subtract, multiply, and divide in all units of measure, using whole numbers, common fractions and decimals. Ability to compute rate, ratio, and percent and to draw and interpret bar graph.
Special Requirements:
Some overtime may required, including weekends.
How to Apply:
To apply, please submit your resume highlighting your relevant experience and interest in the role, you may also email your resume to or call our front office at (310) 537-3750. We look forward to hearing from you!
Pay Range: $17 to $23 per hour
**Please note that the salary range information is only applicable to California. This range is the company's good faith and reasonable estimate of the compensation for this role based on the position's responsibilities, qualifications, experience, and other relevant factors. Actual compensation may vary depending on the selected candidate's specific experience, education, skills, and other relevant factors.
Equal Opportunity Employer
Industrial Tectonics Bearings is an equal opportunity employer. All qualified applicants will receive consideration for employment without regard to race, color, religion, gender, sexual orientation, gender identity, national origin, disability, or veteran status.
This role is subject to compliance with the International Traffic in Arms Regulations (ITAR) and the Export Administration Regulations (EAR), which requires the incumbent to be either a US citizen, lawful permanent resident ("green card" holders) or have refugee or asylee status.
Essential Function Examples:
- Identifies and assembles bearings completely after method of assembly has been established and after inspection of parts has been completed. On non-complex bearings, interprets blueprints and specification sheets to determine requirements for the bearing or component part.
- Sets up standard mechanical and air gages to check bearing components, and partially and/or completely assembled bearings for conformance to standards. Receives instructions from supervisor or designated individual on how to maintain complex inspection equipment.
- Secures first article inspection to verify set-up and continues to check the parts for conformance to standard throughout the course of the run. At the completion of the run, the incumbent obtains inspection buyoff before going to the next job.
- Uses mathematics involving decimals and fractions to operate inspection equipment, check tolerances and fit up of bearings. Must be able to use tables and charts to assist in the use of mathematics.
- Follows assembled bearings to assure they are packed according to specifications and are physically shipped when requested to do so by the supervisor.
- Identifies and assembles bearings completely after method of assembly has been established and after inspection of parts has been completed. On non-complex bearings, interprets blueprints and specification sheets to determine requirements for the bearing or component part.
- Sets up standard mechanical and air gages to check bearing components, and partially and/or completely assembled bearings for conformance to standards. Receives instructions from supervisor or designated individual on how to maintain complex inspection equipment.
- Secures first article inspection to verify set-up and continues to check the parts for conformance to standard throughout the course of the run. At the completion of the run, the incumbent obtains inspection buyoff before going to the next job.
- Uses mathematics involving decimals and fractions to operate inspection equipment, check tolerances and fit up of bearings. Must be able to use tables and charts to assist in the use of mathematics.
- Follows assembled bearings to assure they are packed according to specifications and are physically shipped when requested to do so by the supervisor.
Experience: High school diploma or general education degree (GED), and a minimum of one year of experience in precision bearing assembly using a variety of precision checking techniques.
Knowledge/Skills/Abilities:
Competence to interpret blueprints and decipher documents such as safety rules, operating and/or procedure manuals. Competence to use standard measuring equipment. Ability to add, subtract, multiply, and divide in all units of measure, using whole numbers, common fractions and decimals. Ability to compute rate, ratio, and percent and to draw and interpret bar graph.
Special Requirements:
Some overtime may required, including weekends.
How to Apply:
To apply, please submit your resume highlighting your relevant experience and interest in the role, you may also email your resume to or call our front office at (310) 537-3750. We look forward to hearing from you!
Pay Range: $17 to $23 per hour
**Please note that the salary range information is only applicable to California. This range is the company's good faith and reasonable estimate of the compensation for this role based on the position's responsibilities, qualifications, experience, and other relevant factors. Actual compensation may vary depending on the selected candidate's specific experience, education, skills, and other relevant factors.
Equal Opportunity Employer
Industrial Tectonics Bearings is an equal opportunity employer. All qualified applicants will receive consideration for employment without regard to race, color, religion, gender, sexual orientation, gender identity, national origin, disability, or veteran status.
This role is subject to compliance with the International Traffic in Arms Regulations (ITAR) and the Export Administration Regulations (EAR), which requires the incumbent to be either a US citizen, lawful permanent resident ("green card" holders) or have refugee or asylee status.
Share this job
RBC Bearings